ANATOLIA SONDAJHome / Drill rigs / ANT 18
Underground and inclined surface holes
ANT 18
Designed for underground galleries and horizontal drilling on surface, with 360 degree horizontal and vertical drilling capability and a 120 kW electric power unit that runs quietly and without exhaust in confined spaces.
Configurable with an electric or a diesel power unit to suit the job, the system delivers long service life, reliability and high efficiency through precise control.
Delgi kapasitesi
Drills at 360 degree angles, horizontally and vertically.
A solution shaped by the drilling location
Built for work inside underground galleries. The mast moves through 360 degrees horizontally and vertically, so a hole can be drilled at any required angle and direction. The ANT 18 drills on electric power and trams between locations on its diesel drive unit, which makes it genuinely mobile on site.
Because it accepts both electric and diesel configurations, it also answers inclined drilling requirements above ground.
Technical specification
Power unit
| Configuration | Elektrikli veya dizel |
| Electric motor power | 120 kW |
| Supply voltage | 550 V, 50 Hz |
| Travel diesel engine | Deutz 912FL4, air cooled |
| Hydraulic system pressure | 250–280 bar |
Rotasyon ve ilerleme
| Rotation type | Hidrolik / elektrik |
| Rotasyon hidromotoru | Rexroth A6VM160 |
| Maksimum tork | 600–640 Nm |
| Maksimum devir | 1.200 dev/dk |
| Gear system | Single speed |
| Feed stroke | 1.800 mm |
| Feed rate | 5–12 m/saat |
Mast and positioning
| Positioning angle | 45°–90° |
| Mast inclination | 180° |
| Lateral tilt | 180° |
| Rotation angle | 180° |
| Pullback force | 9.000 kg |
| Push force | 89 kN |
| Clamping system | Hidrolik |
Dimensions and travel
| Weight | 7,5 ton |
| Uzunluk | 5.530 mm |
| Width | 2.440 mm |
| Height | 2.400 mm |
| Minimum tunnel cross section | 5 × 5 m |
| Palet | 9 ton yük kapasitesi |
| Travel speed | 2,5 km/saat |
Hidrolik
| 1. pompa | Rexroth / Kawasaki, 200 L/dk, 250–280 bar |
| 2. pompa | Rexroth / Kawasaki, 65 L/dk, 230–250 bar |
| 3rd gear pump | Rexroth / Kawasaki, 40 L/dk, 180–190 bar |
| 4th gear pump | Casappa, 27 L/dk, 80–120 bar |
| Oil tank | 310 L |
| Cooling | Air cooled (AKG) |
Wireline and circulation
| Wireline hidromotoru | Danfoss / M+S, 315 cc |
| Mud pump | Danfoss, 100 cc hidromotor |
| Hydraulic control unit | Danfoss / Bucher |
| Komponentler | Sun Hydraulics, Parker, Valvoil, Alfa Gomma |
| Filtreleme | Pressure, return and suction |
| Radio remote travel | Opsiyonel |
Sahada
Sessiz operasyon
The electric configuration removes exhaust and cuts noise in a confined drive, which matters as much for ventilation cost as for the crew.
Portable control panel
The control panel can be placed where the operator has the best view of the work and can stay inside the safe area.
Diesel tramming
The travel functions run on the diesel unit, so the machine can move to its next position without needing a power connection.
Not sure which rig you need?
Send us the target depth, the core size, the angles you need to drill and the dimensions of the gallery, and we will decide together which rig is enough for the job.